Drywall Contractor in Kingwood, TX: Repair, Ceilings and Flood Rebuild | The Woodlands Drywall Co.
The Woodlands Drywall Co. is a drywall contractor serving Kingwood, Texas. Kingwood spans Harris and Montgomery counties, and we cover both sides of the county line.
Four jobs account for most of the drywall services Kingwood homeowners ask us to handle: drywall repair for damaged walls, replacement of board ruined by water, ceiling repair for sagging or stained areas, and drywall installation in additions and newly finished rooms. The smaller jobs fall into two main types. Finishing and texture add the coats and surface pattern needed to blend a patch with the surrounding wall, while popcorn removal strips away the sprayed ceiling texture found in older houses. We also build soffits, frame interior walls, and finish commercial interiors.
Kingwood was developed as a 14,000-acre master-planned community, and severe flooding in 2017 sent water through a large part of it, so many walls here have already been rebuilt once. Before we close your wall back up, we check it with a moisture meter. When a room needs to return to use quickly, we fill with setting-type compound, which hardens through a chemical reaction rather than by drying, and we work to ASTM C840, the published standard for hanging and finishing gypsum board.
We have worked as a drywall repair company for 20 years and are fully insured. Call (346) 248-4075 to schedule a free on-site look at your wall, followed by an itemized written quote within 24 hours of the visit.
Get A Free Quote
Why Kingwood Homeowners Call This Drywall Contractor
Much of the work we are called out to handle in Kingwood involves finishing what a fast rebuild left behind. That work comes down to two things: making sure the wall is dry before it is closed and leaving a repair that blends in once the job is finished. The Woodlands Drywall Co. follows the same commitments on every part of that work:
- We confirm the wall is dry with a moisture meter before anything is closed.
- We match the texture and check that match in low-angle light, where a patch shows first.
- The person who walks your job also runs the crew that completes it.
- We specify the board based on what the room requires, and where a room takes water we use moisture-resistant board, priced as a separate line on your quote.
- We are fully insured, and we have been doing this work for 20 years.
- The on-site look costs you nothing, and your itemized written quote arrives within 24 hours.
Kingwood is not the only place where we keep to these standards. We also work as a drywall contractor in Humble, immediately next door, with the same crews handling the work. Call (346) 248-4075 and we will come out to look at the wall with you.
Drywall Contractor Services Across Kingwood, Texas
Much of the interior finish work here was rebuilt quickly after 2017, so you can still find an incomplete rebuild seam, which is a join where the board or texture was never fully finished. These are the drywall services we provide across Kingwood, and together they cover what walls and ceilings in local homes are likely to need.
-
Drywall Repair
Drywall repair is what we do about the holes, door dents, popped nail heads and torn drywall tape that build up through ordinary use. We cut the damage back to solid board, replace bent metal corner bead, the strip that protects an outside corner, and match the surrounding texture.
-
Water Damage Drywall Repair
Water damage drywall repair deals with board that has been wet, and Kingwood calls for it most. Paper-faced gypsum board stains, swells and softens once water sits in it, and paint cannot reverse that damage, so the affected board comes out. Any wall that has taken water is checked with a moisture meter before we close it.
-
Drywall Finishing & Texture
Drywall finishing & texture is the joint compound and surface pattern raw board needs before paint. Because Kingwood homes were finished decades apart, we match the knockdown, orange peel or hand-troweled surface already on your wall.
-
Drywall Installation
Drywall installation adds new board to a room you are changing rather than repairing. We hang, tape and finish additions, garage conversions and reworked rooms, and in bathrooms and laundry rooms we use moisture-resistant board, which holds its shape where the air stays damp.
-
Ceiling Repair
Ceiling repair is the work we do on the surface a leak reaches first. A ceiling cracks along its joints, stains where water has run, and sags once the board loses its grip on the fasteners. Sagging board is removed rather than screwed back into place, then the ceiling is refinished.
-
Popcorn Ceiling Removal
The sprayed ceiling texture installed during Kingwood's earliest phases is removed through popcorn ceiling removal. We then skim the ceiling flat or apply a new texture and prime it before any paint goes on. Because a room's overall finish depends heavily on its ceiling, the refinish is the most important part of the job.
-
Plaster Repair
We use plaster repair for the older, non-drywall surfaces found around the area. Gypsum plaster is troweled onto a wall wet rather than installed as a board, so it requires its own compounds and longer drying times. We patch the cracked areas and feather the edges into the surrounding surface.
-
Commercial Drywall Services
In the offices, clinics and storefronts at Kingwood Town Center, we handle commercial drywall work. We build and repair tenant interiors, the spaces a business leases inside a larger building, while working around your opening hours and containing the dust so your suite can stay open.
-
Metal Stud Framing
Where a wall is framed in steel rather than wood, we use metal stud framing: light-gauge studs set into track, the channel that holds them at the floor and ceiling. Steel does not swell after a soaking the way a wood stud can, and commercial drawings often specify it, so we frame in steel wherever the plan calls for it.
-
New Construction Drywall
New construction drywall is the whole-house hang and finish on a house being built, and construction is still active along the newer edges of the community. We work to the builder's schedule and finalize the finish before the first coat of paint, because changing it afterward means paying for the work twice.
-
Ceiling Drywall Installation
Where an old ceiling has been removed, including ceilings opened during a rebuild, ceiling drywall installation puts new board back overhead. The ceiling board goes on before the walls, allowing the wall board to fit tightly underneath and support its edge.
-
Partition Wall Installation
A new wall that divides a room without carrying any weight is partition wall installation. Home offices, split bedrooms and dens closed off from the hall all begin this way. The new wall meets your existing finish along three edges, and we finish those seams to match the surrounding surface.
-
Drywall Priming & Painting
Drywall priming & painting comes after the finishing work. Fresh board and joint compound absorb paint at different rates, so color dries unevenly on an unsealed wall. PVA drywall primer, a sealer applied before paint, creates a more even surface. Finish painting is optional and is quoted separately from the drywall work.
-
Wallpaper Removal
Rooms papered in the seventies and eighties need wallpaper removal, which strips away both the paper and the old adhesive underneath. Pulling wallpaper off often tears the thin face paper on the drywall beneath, so we seal and repair that surface before any paint goes on.
-
Drywall Soffits & Bulkheads
Drywall soffits & bulkheads are the boxed forms above kitchen cabinets and around ductwork, and a kitchen remodel usually means rebuilding one. The outside corner of a bulkhead is where a poor finish shows first, so we install the corner bead and coat it straight.
-
Soundproof Drywall Systems
Soundproof drywall systems make one room quieter in a house full of hard floors. We install sound-damping panels, heavier boards designed to absorb sound rather than carry it through, along with resilient channel, a metal strip that holds the board away from the framing.
What 2017 Left Behind the Walls
Severe flooding followed Hurricane Harvey through Kingwood in 2017, forcing families out of their homes before the water receded. Paper-faced gypsum board absorbs water and holds it, so interiors across whole streets were opened up and rebuilt within the same few months. Years later, what still bothers you in a room is usually what that fast pace left unfinished, which is why houses signed off long ago still need wet board removed properly.
Rebuilds Done Fast, and What Got Skipped
A straight horizontal line across a wall marks where the old board was cut away and new board spliced in above it. At an outside corner, metal corner bead can sit proud of the surface, standing slightly above the surrounding wall so the angle catches the light. Texture can also change partway along a single wall where one spray pattern meets another. Drywall repair brings the entire wall back to one consistent surface.
Seams and Tape That Opened a Year Later
A joint that looked flat at handover can open months later because of conditions already present when it was closed. Drywall tape bedded in joint compound that had not fully cured moves as the compound dries beneath the coats above it, while a joint closed over framing that was still releasing moisture moves as the timber shrinks. Drywall repair here means opening the joint, removing the tape and rebuilding it from the board out rather than skimming fresh compound over a line that is still moving.
Rooms That Were Closed Up Before They Were Dry
Where board was put back over a cavity that had not finished drying, the signs appear slowly. A brown stain returns through fresh paint weeks after the room is repainted, drywall screws rust and leave faint rings through the finish, and a musty smell comes and goes with the weather. Water damage drywall repair in these rooms means opening the wall and drying the cavity behind it, because sealing over the stain leaves the water trapped where it is.
Free Quote FormWhere We Work Around Kingwood
Kingwood is organized into named villages and subdivisions, each built by its own builder over a distinct period, so homes within the same village resemble one another far more than homes just a short drive away. We work throughout Kingwood on both the Harris County and Montgomery County sides; the four villages below simply show what those differences mean inside a wall, not the limits of where we work.
Kings Forest: Putting a Flooded Wall Back
A Kings Forest house that took water usually needs whole sheets removed rather than just a strip along the bottom, so water damage drywall repair here is a sheet-by-sheet job. The paper facing on gypsum board holds moisture long after a room feels dry to you, and removing the sheet in one piece carries that moisture out with it. New board goes back onto the same framing the old sheets came off, restoring the flat line your wall had before.
Bear Branch: Stained and Sagging Ceilings
Ceiling repair in Bear Branch starts by opening the ceiling back to sound board, so no stained or softened material remains above the new work. The patch is then retextured to match the rest of the room. Because light from a window travels across a ceiling from the side rather than hitting it head on, that low angle casts a shadow from any ridge that sits differently from the surrounding texture. Matching the spray pattern keeps the repaired area from standing out as a patch.
Royal Shores: Making New Work Match Older Walls
In Royal Shores, the common job is drywall finishing and texture on new work that needs to blend into a wall finished years earlier. Knockdown texture is sprayed on as wet joint compound, then flattened with a blade once it begins to stiffen. Flatten it too early and the pattern smears; leave it too long and the peaks stay sharp. Working it at the same stage is what makes walls of different ages look like one continuous surface. Where a sprayer cannot reach, we match the pattern by hand.
Trailwood: New Board in Converted and Added Rooms
Trailwood brings us drywall installation in rooms that were never part of the original house, including garage conversions, enclosed porches and rooms added at the back. Each one meets the original house along a single wall. We tape and finish that junction like any other joint rather than filling it with caulk, because caulk stays soft and shows as a line once the paint goes on. Where the new room contains a shower or washing machine, we hang moisture-resistant board.
Cutting to the Wet Line in a Flooded Home
Once water has been through a room, the question is not whether board needs to come out, but how far up the wall the removal has to go. The flood cut line is the height we cut to, and we set it with a meter against the wall rather than judging it by eye from the doorway. You see the reading before we settle the size of the water damage drywall repair.
How Far Up the Wall the Damage Reaches
A moisture meter is a handheld instrument that shows how much water a material is holding. We take readings up the wall until they return dry, mark the highest wet reading, and cut above it rather than at it. Paper-faced gypsum board draws water upward beyond the level where the water stood, so the stain marks where the water sat while the board carried moisture higher. Cutting at the stain leaves damp board in place and puts new work over wet framing.
What Turns Up Behind the Board
An opened wall usually holds more water than the painted surface suggested. Insulation stays saturated long after the room feels dry, fasteners rust, and the framing can continue holding moisture. If we find established mold growth inside the cavity, we stop the drywall work, document what we found, and refer you to a licensed mold professional before the rebuild continues.
Letting the Cavity Read Dry Before It Closes
New board goes up only after the open cavity meters dry, because closing a wall too soon means opening it twice, and the second opening removes finish work you have already paid for. While the wall is open, we record the readings, photograph the cavity, and prepare an itemized written scope showing what comes out and what goes back. That record is yours to keep. It documents what we measured and when, without making claims about how anyone else will interpret it.
Our drywall experts set that line with you in the room, and the on-site visit is free. Call (346) 248-4075 to schedule one.
The Livable Forest: Tree Cover, Shade and Slow-Drying Rooms
Most of Kingwood sits beneath a heavy pine canopy, and that shade slows how quickly a house gives up water. A failed supply line, an overflowing pan under an air handler, and a roof leak all leave the same slow drying behind them. Gulf Coast air already carries a great deal of moisture, so it pulls little more from a damp wall.
Shade, Canopy and Rooms That Dry Slowly
Rooms on the north side of a house, along with any room kept in shade by the trees, receive little direct sun. Close one off while the rest of the house is heated or cooled, and the air inside holds its moisture longer. A wall can feel dry to your hand while the board behind it is still wet, which is why we check it with a meter before any drywall repair closes it back up.
What Slow Drying Does to Board and Seams
Joint compound hardens by releasing water into the surrounding air, so in a shaded, damp room each coat needs more time to cure before the next one goes on. Our sheetrockers allow for that longer cure time between coats, and when the schedule requires a faster set, we use setting-type compound. Applying another coat over compound that is still damp causes later shrinkage that shows as a faint ridge through the paint.
Cracks That Reopen With the Season
A crack that returns in the same place each year is different from a one-time repair. This region sits on expansive clay soils that swell as they absorb water and shrink during dry spells, so a building on that ground moves through the year and the finish moves with it. Where a crack appears and the direction it runs are clues rather than conclusions. If it keeps returning, widens, or leaves the two sides at different levels, the issue is with the building rather than the wall, and it is worth evaluation by another qualified professional before we fill it again.
Drywall Questions From Kingwood Owners
How much of a flooded wall has to come out?
The meter determines how far up the damage reaches, and that answers two questions at once. The lower sheet almost always comes out whole because a seam across the middle of a wall is the hardest one to hide under paint and light, making full-sheet replacement cheaper than trying to lose that joint. What the reading settles is whether the sheet above it also has to come out.
How do you decide where the wet line is?
A meter reading decides it, taken across the entire wall rather than only at the spot that looks worst. The cut goes above the highest wet reading, not level with it. Once the board is removed, we check the framing behind it again because a stud can hold more water than the sheet that covered it.
Which parts of Kingwood do you cover?
All of Kingwood, including both counties, is covered, so the Harris County side and the Montgomery County side are quoted the same way. We work out of The Woodlands, a short drive along the same corridor, which makes Kingwood part of a normal working day rather than a special trip. You are not waiting for the week a crew happens to be nearby.
What happens if you find mold behind the drywall?
The work stops there. Established mold growth is not drywall work, so we leave the wall open while you bring in a licensed mold professional before anything is closed up. The rebuild is paused rather than canceled, and once the mold work is complete, we resume the drywall portion at the open wall under the scope you already agreed to.
Do you write anything up for my insurance?
Yes, you receive an itemized written scope of the work along with photographs of what we found behind the board. Nobody here is an adjuster, so we do not file, negotiate or interpret a claim, and your deductible is never absorbed or discounted. The scope and photographs are yours to give to your insurer, and the prices remain as written regardless of how the claim is handled.
Is it cheaper to patch this wall or replace the sheet?
It depends on how much of a single sheet needs patching. One hole is cheaper to fill. Once multiple patches on the same sheet begin to overlap, the sanding, feathering and texture matching around them cost more than replacing the sheet, and you end up paying twice to finish the same wall. We count the patches sheet by sheet and tell you which option costs less.
Do you only repair drywall, or do you also handle ceilings and textures?
Both, along with much more. Our sixteen kinds of drywall work range from a single patch to a whole-house hang. Ceilings, texture, popcorn removal and priming each appear as separate lines on the quote, so you can see exactly what each one adds to the price and remove any you do not want.
If these leave anything unanswered, ask us while we are in the room.
Get a Free Drywall Estimate in Kingwood
A free on-site estimate begins with one of us in the room, looking directly at the wall or ceiling you want fixed. Within 24 hours of that visit, you receive a written quote with an itemized scope, so the price you plan around is in writing before the work begins. Financing is available for qualifying work. Call The Woodlands Drywall Co. at (346) 248-4075 or use our quote form to request your free on-site estimate.